Just How to Remove as well as Replace a Bath Tub.
Just How to Remove as well as Replace a Bath Tub.
Blog Article
The article which follows involving How to Install a Bathtub is seriously compelling. Don't overlook it.
Mounting a bathtub isn't precisely brain surgery, however it does need strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old tub with a new one is likewise a moderately hard project. If the old tub is easily easily accessible, the job can relocate speedily; if you have to open a wall surface to get rid of the old bathtub and place the new bathtub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will require an assistant to move out the old tub as well as set in the brand-new one. Ensure you have certified yourself for the work and fit attempting it. As opposed to employing a contractor to take control of a halfway-completed job, it is much better to consider using one prior to you begin. Chances are you may require an expert plumber to make tube connections.
This write-up will certainly assist you set up a new tub in your restroom if you have currently acquired a brand-new tub and don't need to alter the plan of your previous water system pipes.
Your tools as well as product list need to comprise the following:
Preparing for the Installation
First of all, the supporting frame supplied with the bath must be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to see to it that if the tap includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps system to stop strain on the bath tub.
Fit the flexible faucet adapters to the bottom of the two faucets making use of 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final setting.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is detach the supply of water. After doing so, switch on the faucets to drain any water staying in the system. The procedure of getting rid of the existing taps can be quite troublesome because of the limited accessibility that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have been removed, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old securing substance.
Prior to moving on to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Making use of both wooden boards under its feet, place the bathtub in the needed setting. The wooden boards are practical in equally spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto four small points.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the tub until the spirit level reads level.
To install taps, fit all-time low of the outermost flexible tap connector to the appropriate supply pipe by making a compression join; after that do the very same for the various other faucet.
Turn on the water system as well as inspect all joints and new pipework for leaks and tighten them if essential. Load the tub and likewise inspect the overflow outlet and the normal electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also securing around the tub ought to wait until the bath tub has actually been utilized at least when as this will certainly settle it into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in area between the tap as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet ends first, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack a stiff seal, causing the water to penetrate the wall surface in between the bathroom and the tiling, resulting in issues with wetness and also possible leaks to the ceiling below.
You can select from a selection of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Remember to always fill the bath tub with water prior to securing, to enable the motion experienced when the tub is in use. The sealer can split relatively early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise quickly available on the market. It is suggested to fit the floor tiles utilizing water-resistant or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate reader about How to Install a Bathtub Yourself, I assumed sharing that excerpt was worth the trouble. Enjoyed our blog? Please share it. Help others check it out. I praise you for your time. Come back soon.
Get Started Report this page